Features :
- Extra Duration & Voltage
- Reliable
Spec :
- Fits Various of EP Cars & Starter Boxes
Read the rest of this entry »
No Comments »
Features :
- Long run time
- High quality wire and connector
Spec :
- Ideal for use in most cars
- Universal type connector
Read the rest of this entry »
No Comments »
Front bumper weight is improved, and the steering wheel control
performance is improved.
28.6 grams in weight(Only the plate is weight. )
Source : RC Tagu
No Comments »
Posted by: rceasy in XRAY
Souring from neo-buggy.net for the XRAY XB8 New Concept prototype spy pictures.
Read the rest of this entry »
No Comments »
E4FS Main Features:
- Most lipo battery & brushless motor can be used
- New 3mm carbon fiber, 96mm wide narrow chassis
- New 2.5mm carbon top deck (with two new alum. posts linked to chassis for strength)
- Front/rear 3mm carbon shock tower
- Front/rear hard coated alum. 7075 universal drive shaft
- Alum. 7075 turnbuckles
- New Shocks
- New thickened arms
- New widened belts
- Single bell crank steering system
- Front/rear ball differential (quick release design)
- New lightweight nylon pulley
- Alum. 7075 FF & RR hinge pin mount
- Alum. 7075 bulkhead
- New rear lower Flying Wing arm for foam tires (1 degree toe-in angle)
- New front lower Flying Wing arm
- Centralized motor and battery design
- Quick release main shaft
- Motor cooling mount
- Front/rear anti-roll bar
Read the rest of this entry »
No Comments »
Posted by: rceasy in Kyosho
ASF 2.4GHz MINI-Z Racer MR-02LM
- Porsche 962 C
- Porsche 962 C LH No.10 ‘86 LeMans Version
Run 40 Cars simultaneously…. Kyosho introduce the all new AST 2.4 GHz Mini-Z Racer MR-02LM
Read the rest of this entry »
No Comments »
Posted by: rceasy in Kyosho
Ergonomics (human engineering) design that draws out performance of 2.4GHz. Advanced design that can use function of average Haiendopropo stylish.
Read the rest of this entry »
No Comments »
Posted by: rceasy in Ko Propo
AC100V and DC12V power and can be used for charging and discharging equipment. Tamiya and types of cancer that includes a connector for charging.
- Input power source AC100V & DC12V
- corresponding battery nickel hydrogen and the nicad battery 1 - 10 cells (1.2 - 12.0V) the lithium ion lithium polymer battery 1 - 4 cells (3.6 - 14.8V) the lead batterycell (Pb) 2V, 6V, 12V & charge capacity 300 - 5000mAh
- charging current 0.3 - 5.0A
- discharge current 0.3 - 2.0A
- case size 161×144×83mm (projection ones are excluded)
- Weight 638g
Source : KO Propo & Pro-shop Futaba
No Comments »
Posted by: rceasy in Yokomo
The option part which is added
- Front ball diff.
- center one way
- aluminum rear solid axle
- Aluminum suspension mount front and back
- stabilizer front and back
- bumper weight set
- aluminum joint sleeve
- aluminum make special battery post
- special carbon battery plate
- multiple body post
- titanium turn buckle set
- titanium bis set
Read the rest of this entry »
No Comments »
Posted by: rceasy in Yokomo
While raising the pitching rigidity of the chassis front section substantially, it is the front chassis brace which leaves the suppleness of roll direction. While by the fact that balance of chassis rigidity is changed, increasing cornering early steering wheel responsiveness, you pull out the sense of security with the pliant roll. Of course ideal, the eye which the chassis was seen with the vivid blue alumite changes substantially as a dress rise item. As for the screw for installation please use those which have belonged to the kit. Clearance of the steering wheel crank a little becomes large, but there is no hindrance in travelling. If the spacer shim of 4.0mm (ZC-S40 - 380) 0.5mm thick extent you can put the one where being shaky becomes matter of concern, being to cancel, please try. In addition the aluminum steering wheel bell crank post of another sale option (SD-202P - 550) with installation rigidity of the post increases by the fact that it jointly uses, can expect also further steering wheel response improvement.
Read the rest of this entry »
No Comments »
Entries (RSS)