Translate :

First pictures of the new middle class chassis from Tamiya emerged. Most remarkable characteristic of the new kardanangetriebenen TB-03 chassis is its Daempferanordung which very the TA-05 IFS resembles and exhibits therefore the Daempferanordung flat on the inside at the front axle. The wheel carriers are obviously this-same like those of the TA-05 IFS R. The Akku is supplied as used by large chassis openings from down with fresh air and for the engine gives it chamfered openings under the chassis. The internal reduction amounts to 2.44:1 and available should the chassis off approx.. June 2008 its.

Read the rest of this entry »

TB EVOLUTION 5 MS

Available Jun 21, 2008

* High ended model of shaft 4WD, TB evolution furthermore evolution.
* Throwing the various trends which are obtained from the race activity of TRF. The center support steering wheel which is similar to TRF416, adopting upright of 1050 bearing specification which corresponds to high load.
* The divided type upper deck which designates the rear section as the aluminum make was adopted, operating efficiency of spur-gear exchange was raised.

Read the rest of this entry »

Sourcing from RCmagazine Japan for the all new Tamiya TB Evolution 5 MS Edition, which will be shown in the coming 47th Shizuoka Hobby Show 2008.

Source : RCmagazine

Available Apr 26, 2008

The reality body and the real four running mechanic, running, decorating, it can enjoy

It is the electromotive radio control car assembly kit which reproduces Mitsubishi Pajero metal top wide high popularity was gained in 1993 as cross country 4WD which is handled from the appearance and off load to town use. It loads the motor onto the front midship, the front transmitting power to the gear and the rear with the propeller shaft. Actual car mood fully mechanical chassis constitution is charm. The underside the front of the double wishbone, equipping also the oil damper in 4 links rigid rear suspension, showing high travelling efficiency. Furthermore the tire and the wheel realize running the scale impression in addition to the ABS resin make body which overflows plus. In headlight and fog lamp LED installing possibility. Installing TLU-01 and the like of selling separately, it can enjoy also light illumination.

Read the rest of this entry »

Available : Apr 26, 2008

The machine for engine buggy introduction which is complete basic efficiency

While making light exhaust noise echo, it is the completion engine RC buggy which can enjoy exciting off load travelling. As for the engine which is loaded Tamiya FS-15FD of aerodynamic volume displacement 2.5cc. As for the chassis high rigidity the shaft drive 4WD which adopts the double deck frame. High grip equipping the spike tire in the double wishbone suspension which equips the oil damper, it does not choose the place where it runs. In addition, as for body & rear wing lightweight polycarbonate make. The gun metal the wheel of the body, and the lead-lead where the line of the lead-lead enters into keynote makes intimidating be effective. Loading the choke pump equipped 65cc fuel tank, it can enjoy travelling of approximately 5 parts in 1 tank.

Read the rest of this entry »

Tamiya Show their new 1:8 TRF 801XT full-race truggy at RCX 2008.

Source : RC Car Action

Available : Apr 26, 2008

Challenge a thrilling lock section

It is an electric radio control car assembly kit that reproduced 40 factions released from 1960 to 84 years in the Toyota land cabin cruiser also that one of the four-wheel drive cars known most in the worlds. The chassis is CR-01 developed for a crawling lock. Equipment of the challenge to the lock section such as a large diameter tires with a crowded tread pattern on shaft drive 4WD of four link suspension with Radarfram and the oil damper that had used the rod made of aluminum and possible differential locking devices and sides it turned and the bead lock wheels was fully loaded with the side made of aluminum member and the crossmember made of the resin. the composed high rigidityCan it climb to crawl the slope in the rock at which it looks up while shaking the body made of the polycarbonate reproduced in the round, and it enjoy a thrilling running similar to a crawling lock of a real car.

Read the rest of this entry »

Porsche 911 GT3 Cup VIP 2007 (TT-01 Chassis Type-E)

Available : Apr 26, 2008

The machine for the one make-up race of the highest peak

It is developed for highest peak “Porsche super-cup” of the one make-up race that has been held in ten countries in the world, and delivery 911GT3 cup car in a private team. Porsche especially manages the machine, and the assembly kit of the electric radio control car that reproduces VIP car that guest players drive at each race. The modeled body is made of the polycarbonate to enough actually feeling as for the form with power. It can enjoy the light lighting by setting high luminance LED of two headlight lights (white) and two rear light lights (red). Moreover, the logo etc. of the pinstripe and the Porsche of gotten Gold and white were prepared in a chic black color in the sticker.

Read the rest of this entry »

Available Apr 26, 2008

The potential kept secret in ..Sharp.. form

Coloring of ..low form.. black it & red in which the edge is effective shows Sharp the body lower. As for the bird at the velocity, completion and electric radio baggy control 2WD with falcon’s name is a neo-falcon. An excellent bathtub frame in the weight balance in low center of gravity is equipped with double wishbone four-wheel independent suspension. It spikes it to the tire combined with Astoraldisshuhoel that a stelliform design is unique by demonstrating the grip power with an enough Waidoglubd and rear wheel that the front wheel is excellent in directionality. It is made of the polycarbonate ..Sharp.. light a body and large-scale Riyauing strong in shock.

Read the rest of this entry »

TA05-IFS R Chassis Kit

Available May 24, 2008

* In the TA05-IFS chassis, it is the kit which equips 30 kind thing parts which it is essential to race anew.
* The aluminum of the new part it starts shaving, make the center plate and the belt for the 37T-18T pulley setting.
* The center plate of floating type making the chassis easy, to be twisted raises the steering wheel response, the drive belt actualizing the decrease of drive resistance.

Read the rest of this entry »